Bosch SHP65TL5UC Repair Instructions Download | Manualshive

Page: 10 / 82

background image

702_58300000170749_ara_en_c

Page 10 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

2.6

Attaching mounting brackets

Top mounting is used for countertops made of wood or other
materials that can be easily drilled. Side mounting is used for
countertops made of marble, granite, or other hard materials that
cannot be easily drilled.

2.6.1

Attaching mounting brackets to dishwashers

•

Mounting brackets have a tab to be inserted into tank flange

slots. Use the taller slots on the outside of tanks, not the
shorter slots inside of those “outside” slots.

•

Insert the bracket tab into the correct slot and snap the

bracket down into the tank.

•

Crimp the bracket tab downward with pliers to fix the bracket

in place.

2.7

Installing toe kicks

Depending on the model, toe kicks may or may not have
mounting brackets. Toe kicks without mounting brackets are
screwed directly into the dishwasher base.

•

For dishwashers with mounting brackets, slide brackets into

dishwasher base and fasten with supplied screws.

•

Tilt top of toe kick up behind outer door and drop bottom of

toe kick in place next to mounting brackets or dishwasher
base.

•

Fasten toe kick in place with two (2) supplied Phillips #2

screws.

•

Snap decorative plastic screw caps over screw heads.

«
...
8
9
10
11
12
...
»

Summary of Contents for SHP65TL5UC



















































































Reviews:

No comments

Related manuals for SHP65TL5UC

DW60A608 Series

Brand: Samsung Pages: 72

Brand: Samsung Pages: 90

Brand: Samsung Pages: 20

Brand: Samsung Pages: 106

Brand: mabe Pages: 88

Brand: Galanz Pages: 14

Brand: GE Pages: 12

Brand: Parmco Pages: 48

Brand: Fisher & Paykel Pages: 76

Brand: HomeKing Pages: 52

Brand: Fagor Pages: 10

Brand: JBM Pages: 36

Brand: Baumatic Pages: 29

Brand: Zanussi Pages: 36

Brand: Zanussi Pages: 32

Brand: Samsung Pages: 118

Brand: GE Pages: 16

Brand: GE Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands