Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 63 | Manualshive

Page: 63 / 282

Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 63

8.2.2 Control Cables

The following requirements are applicable to the signal connection wiring:

●

Flexible cables with wire end sleeves

●

Cable cross-section: 0.5...1.0 mm

2

●

Cable cross-section for connectors with insulation sleeves: 0.75 mm

2

●

Analog inputs AI, +10 V and GND: use shielded cables

●

Digital inputs X1...X4, SC, +24 V and COM: use shielded cables

●

Analog outputs AO and GND: use shielded cables

●

RS485 communication: use shielded twisted pair cables

Recommendations on cable insulation stripping:
Please strip the insulation of control cables according to the dimensions given

below. Too long stripping may cause short circuit of adjacent cables; too short

stripping may lead to cables becoming loose.

Fig. 8-3: Cable insulation stripping length

Please follow the steps below for wiring of control terminals.
Step 1: Switch off the frequency converter before performing wiring.
Step 2: Deactivate the control signals in the wiring process.
Step 3: Switch on the frequency converter.
Step 4: Set respective parameters.
Step 5: Activate respective control signals.

VFC 3210

Bosch Rexroth AG

Frequency Converter Wiring

DOK-RCON04-VFC3210****-IT01-EN-P

35/253

«
...
61
62
63
64
65
...
»

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments