manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 49 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 49

6.1.7  Protection

Over current protection, over- / under- voltage protection, surge current / short circuit protection, in-

put / output phase loss protection, converter over- / under- temperature protection, motor overload

protection, motor over temperature protection, direction lock protection, analog input broken wire de-

tection, etc.

6.1.8  Conditions

Rated ambient temperature

-10...40 ℃

Derating / ambient temperature

1.5 % / 1 °C (40...50 °C)

Rated storage temperature

-20...60 ℃

Rated altitude

≤ 1,000 m

Derating / altitude

1 % / 100 m (1,000...2,000 m)

Relative humidity

≤ 90 % RH (No condensation)

Degrees of protection

IP 20 (Mounting on the metal wall in control cabinet )

Degrees of pollution

2 (EN 50178)

Vibration

10 Hz ≤ f ≤ 57 Hz amplitude: 0.075 mm
57 Hz < f ≤ 150 Hz acceleration: 1 g

Mounting mode

Wall mounting

Cooling type

Natural cooling (≤ 0K75)
Enforced air cooling (≥ 1K50)

Certification

CE

VFC 3210 

Bosch Rexroth AG

Frequency Converter Overview

DOK-RCON04-VFC3210****-IT01-EN-P

21/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments