Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 34

Page: 34 / 282

1.3.3 Hazards by Improper Use

●

High electrical voltage and high working current! Danger to life or serious in-

jury by electric shock!

●

High electrical voltage by incorrect connection! Danger to life or injury by

electric shock!

●

Dangerous movements! Danger to life, serious injury or property damage by

unintended motor movements!

●

Health hazard for persons with heart pacemakers, metal implants and hearing

aids in proximity to electric drive systems!

●

Risk of burns by hot housing surfaces!

●

Risk of injury by improper handling! Injury by crushing, shearing, cutting, hit-

ting!

●

Risk of injury by improper handling of batteries!

●

Risk of injury by improper handling of pressurized lines!

Bosch Rexroth AG
Safety Instructions for Electric Drives and Controls

VFC 3210

6/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Search results

Summary of Contents for Rexroth VFC 3210

Reviews:

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 34 / 282

Search results

Summary of Contents for Rexroth VFC 3210

Reviews: