manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 197 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 197

Fig.  12-55:   User-defined V/f curve when [C2.05] ≥ [C1.08]

Slip compensation factor configuration
This function is used to compensate [C1.12] 'Motor rated slip compensation' ac-

cording to the actual applications in V/f control.

Code

Name

Setting range

Default

Min.

Attri.

C2.07

Slip compensation factor

0…200 %

0

1

Run

●

0 %: No slip compensation
The slip compensation function is deactivated.

●

1...100 %: Full slip compensation
Example: [C1.12] = 2.50 Hz, [C2.07] = 100 %
The actual slip compensation is 2.50 Hz x 100 % = 2.50 Hz.

●

101...200 %: Over slip compensation
Example: [C1.12] = 2.50 Hz, [C2.07] = 200 %
The actual slip compensation is 2.50 Hz x 200 % = 5.00 Hz.

VFC 3210 

Bosch Rexroth AG

Functions and Parameters

DOK-RCON04-VFC3210****-IT01-EN-P

169/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments