manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 173 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 173

12.9.8  PID Status Indication

Code

Name

Setting range

Default

Min.

Attri.

E4.32 PID engineering value detection width

0.01...100.00

1.00

0.01

Run

E2.15 Relay 1 output selection

18: PID reference engi-

neering value arrival

1

–

Stop

[E4.32] 'PID engineering value detection width' is used to set the tolerance win-

dow  between  [d0.70]  'PID  reference  engineering  value'  and  [d0.71]  'PID  feed-

back engineering value'. When the difference between reference and feedback is

within the detection width, the value arrival signal will be active via DO1 output.
Set [E4.32] = 

│

[d0.70] - [d0.71]

│

/[d0.70] x 100 %

Fig.  12-40:   PID engineering value detection width

VFC 3210 

Bosch Rexroth AG

Functions and Parameters

DOK-RCON04-VFC3210****-IT01-EN-P

145/253

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments