Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 122

Page: 122 / 282

Adjust the setting frequency by panel button
The setting frequency of the first and second frequency setting sources can be

adjusted by pressing the <▲> / <▼> button on the operating panel.

Code

Name

Setting range

Default

Min.

Attri.

E0.00 First frequency setting source

1: Panel button

–

Stop

E0.02 Second frequency setting source

–

Stop

E0.07 Digital setting frequency

0.00...[E0.09] Hz

50.00

0.01

Run

Adjust the setting frequency by analog inputs
When analog input AI1 is used as the frequency setting source, the relationship

between AI1 and the setting frequency is shown as the figure below:

Fig. 12-7: AI1 and setting frequency

To set analog input AI1 properly, see

chapter 12.2.2 "Analog Input

Configuration" on page 81

Bosch Rexroth AG
Functions and Parameters

VFC 3210

94/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Search results

Summary of Contents for Rexroth VFC 3210

Reviews:

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 122 / 282

Search results

Summary of Contents for Rexroth VFC 3210

Reviews: