manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 120 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 120

Frequency setting sources combination
It is possible to combine the two frequency setting sources for complicated ap-

plications.

f

SRC1

First frequency setting source

f

SRC2

Second frequency setting source

f

Set

Setting frequency

Fig.  12-6:   Combination of frequency sources

Code

Name

Setting range

Default

Min.

Attri.

E0.04

Frequency setting source combination

0...6

0

–

Stop

●

0: No combination
By default, actual setting frequency is set by 'First frequency setting source'.

'Second  frequency  setting  source'  can  be  activated  by  one  of  digital  inputs,

see 

chapter "Frequency setting source switching" on page 91

.

●

1: First frequency s Second frequency setting
The actual setting frequency is the result of the addition operation of the first

and second frequency setting sources.

●

2: First frequency setting - Second frequency setting
The actual setting frequency is the result of the subtraction operation of the

first and second frequency setting sources.

Bosch Rexroth AG
Functions and Parameters

 VFC 3210

92/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments