manualshive.com logo in svg

Bosch Rexroth VFC 3210, Operating Instructions Manual, Page: 118 / 282

Share
Download
Bosch Rexroth VFC 3210 Operating Instructions Manual Download Page 118

12.4.2  Select the Frequency Setting Source

General setting
Different frequency setting sources can be selected by setting parameter E0.00

'First frequency setting source' or E0.02 'Second frequency setting source'.

Code

Name

Setting range

Default

Min.

Attri.

E0.00 First frequency setting source

0...21

0

–

Stop

E0.02 Second frequency setting source

0...21

2

–

Stop

●

0: Panel potentiometer
The setting frequency is set by adjusting the potentiometer on the operating

panel.

●

1: Panel button
The  setting  frequency  is  set  by  parameter  E0.07  'Digital  setting  frequency'.

Pressing  <▼>  and  <▲>  buttons  on  the  operating  panel  will  decrease  and  in-

crease the output frequency respectively when the frequency converter is run-

ning.

●

2: AI1 analog input
The setting frequency is set by AI1 input.

●

11: Digital input Up / Down command
The setting frequency is set by command of Up / Down / Reset via digital in-

puts.

●

20: Communication
The  setting  frequency  is  set  by  engineering  software,  PLC  or  other  external

device via Modbus protocol.

●

21: Multi-speed settings
The setting frequency is set by multi-speed settings.

Bosch Rexroth AG
Functions and Parameters

 VFC 3210

90/253

DOK-RCON04-VFC3210****-IT01-EN-P

Summary of Contents for Rexroth VFC 3210



























































































































































































































































































Reviews:

No comments