Bosch rexroth SB24 Instruction Manual Download Page 21

Page: 21 / 78

About these products 21/78

RE 66170-B/2019-05-15, Control block SB24/34, Bosch Rexroth AG

5.3.4 Port designation

The port designation consists of a letter (e.g.

) and the side designation

(

refers for example to the inlet port on the consumer port side (top).

Table 6: Ports

Denomination

Port for

A1…6

Consumer

B1…6

Consumer

a, b, c

Control, signal

P1…6

Inlet

PD1…6

Supply pressure diagnosis

R1…6

Tank, return flow

Rx1…6

EHS pilot oil return flow

RfB1…6

Secondary pressure relief valve return flow (consumer port B) (depressurized)

X1…6

EHS pilot oil supply

XD1…6

EHS pilot oil supply diagnosis

Yin1…6

LS signal input

Yo1…6

LS signal output

YoD1…6

LS signal output diagnosis

Rc1…6

Coupling relief

, ,

Tie rod

Block mounting

5.3.5 Flange figure

Denomination Port for

Information

Inlet

Block return flow
Secondary pressure relief valve return
flow (consumer port B) (depressurized)

optional

LS signal

Clean oil return flow

optional

EHS pilot oil return flow

optional

EHS pilot oil supply

optional

, ,

Tie rod

Summary of Contents for rexroth SB24















































































Search results

Summary of Contents for rexroth SB24

Reviews:

Related manuals for rexroth SB24

Brands by name

Popular brands

Bosch rexroth SB24, Instruction Manual

Search results

Summary of Contents for rexroth SB24

Reviews:

Related manuals for rexroth SB24

Brands by name

Popular brands