Bosch rexroth MS2N03-A Operating Manual Download

Page: 30 / 72

30 / 72

MS2N

Storage

Bosch Rexroth AG

R911347581, Edition 05

•

Occurring radial force and axial force with

force application point

•

Installation position (horizontal, vertical with

the shaft end pointing to the top or bottom)

•

Mean speed

For radial force diagrams, refer to the project

planning manual.

5.2.11 Frame size, installation type

The motors can be installed horizontally and ver-

tically with the shaft end pointing to the top

or bottom. The mounting variants comply with

the IM code according to EN 60034-7:1993 +

A1:2001 for design and installation type.

Code I / Code II (EN 60034-7)

IM B5 / IM 3001

Flange attachment on

the drive side of the

flange

IM B35 / IM 2001
(only MS2N13)

Foot installation, feet

below, with additional

flange mounting on

drive side of the flange

IM V1 / IM 3011

Flange attachment on

the drive side of

the flange, drive side

facing down

IM V3 / IM 3031

Flange attachment on

the drive side of

the flange, drive side

facing up

Avoid liquid at the drive shaft or the shaft sealing

ring in case of vertical installation according to

IM V3. For further information regarding the pro-

tection class, see

⮫

Chapter 5.2.6 “Degree of

protection ” on page 23

5.2.12 Coating

One-layer standard varnish (1K), water-based, in

conductive form, RAL9005 jet black
An additional varnish with a coat thickness of

max. 40

µm is allowed.

Protect all safety notes (stickers), type plates and

open connectors with a painting protection when

painting additionally.

5.2.13 Noise emission

The typical sound pressure level Lp(A) is speci-

fied for the speed range 0 rpm up to the rated

speed. The installation situation affects the noise

emission.

Transport and storage

6.1

Storage

Store the motors in their original packaging

in a dry, dust-free, vibration-free and light-pro-

tected place without direct solar radiation. Please

observe classes 1K21, 1B1, 1C1, 1S10, 1M11

specified for storage acc. to DIN EN 60721-3-1.
Please observe the following classification limita-

tions:
Table 6: Classification limitation

(DIN

IEC

60721-3-1)

Bearing

Ambient temperature

-25 … +55 °C

Relative air humidity

5 … 75

Absolute air humidity

1 … 29 g/m³

Direct solar radiation

Not permitted

Shock load

⮫

Chapter 6.3 “Shock

load during transport und

storage ” on page 32

NOTICE

Damage due to moisture and humidity!

−

Protect the products from dampness and

corrosion.

−

Store them only in rainproof and dry rooms.

Additional measures have to taken upon commis-

sioning to ensure smooth functioning – irrespec-

tive of the storage time which may be longer than

the warranty period of our products. Warranty

extension is not a consequence.

Summary of Contents for rexroth MS2N03-A









































































Search results

Summary of Contents for rexroth MS2N03-A

Reviews:

Related manuals for rexroth MS2N03-A

Brands by name

Popular brands

Bosch rexroth MS2N03-A, Operating Manual

Search results

Summary of Contents for rexroth MS2N03-A

Reviews:

Related manuals for rexroth MS2N03-A

Brands by name

Popular brands