manualshive.com logo in svg

Bosch rexroth M1, Instruction Manual

Share
Download
Bosch rexroth M1 Instruction Manual Download Page 28

28

/54

 

Control blocks for mobile applications

 | Installation

Bosch Rexroth AG, RE 64025-B/2021-08-12

Series

Dimension

Property class

Tightening 
torque [Nm]

Screw-in depth 
[mm]

ROM8

M8

8.8 / 10.9

27 / 40

1)

RS12

M8

8.8 / 10.9

27 / 40

12

RS14

M10

8.8 / 10.9

54 / 79

1)

RS15

M10

8.8 / 10.9

54 / 79

18

RS20

M12

8.8 / 10.9

93 / 137

12…15

SM 12

M8

8.8 / 10.9

27 / 40

10

 1)

SP-08

M8

8.8 / 10.9

25 / 30

10 … 14

1)

SX 10

M8

8.8 / 10.9

27 / 40

1)

SX 12

M10

8.8 / 10.9

54 / 79

1)

SX 14

M10

8.8 / 10.9

54 / 79

1)

1

)

 Through bore in housing; the screw-in depth depends on nut thread material.

7�5�5  Completion of assembly
1� 

Remove any attached transportation aids. 

CAUTION! 

Operation with protective plastic plugs!

Operating the control block with protective plugs may result in injury or damage 
to the control block.

 

▶ Before commissioning, remove all protective plugs and replace them with 

suitable line connections or pressure-proof, metal threaded plugs.

2� 

Remove the transport protection.  
If necessary, the control block may be delivered with protective covers and 
protective plugs. They are not pressure-resistant and have to be removed prior 
to connection. Use a suitable tool for this to prevent damage to the sealing and 
functional surfaces. If sealing or functional surfaces are damaged, contact your 
Bosch Rexroth service partner or the service department of the manufacturer's 
plant for the control block.

Ports intended for connecting lines come with protective plugs or threaded 
plugs, which serve as transport protection. All ports required for the function 
must be connected. Failure to do so could lead to malfunctions or damage. If 
a port is not being used, it is to be plugged with a threaded plug since 
the protective plugs are not pressure-resistant.

7�5�6  Connecting the control block mechanically

Connection of actuation elements including tolerances is illustrated in the offer 
drawing. The tightening torques are to be selected according to the actuation 
elements. There must not occur any radial forces during actuation!

 

▶ At commissioning, make sure that the tongue is in the zero position 

(control spool in the central position).

Summary of Contents for rexroth M1























































Reviews:

No comments

Brands by name

Popular brands

Load more brands