Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 171

Page: 171 / 382

motor connection

motor temperature monitoring and motor holding brake

XS2

shield connection (motor power cable)

Fig.6-70:

Connections at power section (bottom)

Description of the Connection Points

The connection points are described in detail in chapter

8 Functions and Elec‐

trical Connection Points , page 241

Touch Guard

The touch guard is described in detail in chapter

9 Touch Guard at Devices ,

page 291

6.4

HMD01 Power Sections

6.4.1

Brief Description, Usage and Structure

Brief Description

The HMD01 inverters are part of the Rexroth IndraDrive M product range and

are used to operate 2 single axes.

Usage

The different types are used as follows:

Type

Usage

HMD01.1E-Wxxxx-NNNN

●

double-axis device

●

Operation of two three-phase a.c.

motors (asynchronous or synchro‐

nous motors).

Fig.6-71:

Usage of HMD01

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 161/369

Power Sections for Inverters - IndraDrive M

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands