Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 79 | Manualshive

Page: 79 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 79

Information Area

Information texts and error messages can be displayed in the information area

during operation.

Line Number

The sequential number of the selected line is shown in the second area. The

column is not assigned.

The fields "Open applications" and "Current language" are assigned

by the system. If subroutines are branched, these are also entered

as "Open applications". In this case, the applications cannot be

toggled. Otherwise, the relationship of the programs get lost.

Functional Scope of the Block Search

The block search provides the possibility to start NC processing within the se‐

lected main NC program. This function acts like an absolute jump from the

program start to the target block. The selected program has to be at program

start.
Using the long cursor, the operator selects the desired target block to which it

is to be jumped from the program start.
After having triggered "NC start", the NC begins program processing starting

at this block and based on the current machine and control states. Afterwards,

it is switched to a special NC screen. The previous blocks are not executed or

taken into account.

Starting the Application

The default M-key assignment is the "Block search" key in the "Program func‐

tions" level
When "Block search" is called, the selected NC program is displayed.
The cursor is normally located on the first block in the displayed NC program.

If the program has already been processed previously in the block search, the

previously selected block is marked.

Block Search to Main Block

Generally, the block search is used to position and start a main block that con‐

tains all required geometric and technological data for a continued program

operation, especially the tool replacement.

Block Search on Auxiliary Block

The block search can also be used to position and start any NC block (auxiliary

block). Therefore, the operator has to set the required geometric and techno‐

logical data in "MDI operation" before.
In doing so, the conditions required on the machine for the actual entry block

can be set up.

Selecting the target block

The target block of the displayed NC program can be selected with the cursor

keys.

Note that the selected NC block number must not exist several

times in the NC program. The system jumps to the block number

found first.

Start block search

Pressing the F-key "Apply block" starts the block search and closes the appli‐

cation.

Functional Scope: Block Pre-run

Block pre-run is a function for testing and positioning NC programs so that the

operating procedure can be started at any block in the NC program/subroutine.

Block pre-run is an extension of the NC function "Block search".
Block pre-runt is used to create the required states in the control and machine.

The block pre-run requires a target block being specified. The target block can

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

77/301

Operation Modes

«
...
77
78
79
80
81
...
»

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Reviews:

No comments