Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 248

Page: 248 / 304

Properties of the Energy Monitor

The energy monitor shows the power consumption of the
●

latest ten measurements as bar chart

●

individual drives as well as

●

individual auxiliary equipment.

Components

The energy monitor consists of the following sections:
●

header

●

main screen and

●

F-keypads

11.2.2

Commissioning the Energy Monitor

Prerequisites

The energy monitor gets the data to be displayed via the PLC function block

"MT_4EEGuiMonitor". To do so, the respective function block has to be inte‐

grated into the PLC program and wired (also refer to the PLC Programming

Manual).
Furthermore, the energy monitor has to be configured. It is to be started under

"Production data" with <F2>, the configuration menu has to be started with

<F8> and the configuration has to be carried out as described in the following

subchapters.

Configuration of the Energy Monitors - Drives

Fig.11-8:

Configuration of the energy monitor - Drives

Within the "Energy Monitor - Drives" window, all SERCOS drives have to be

entered. To achieve this, the following functions are available:
+: Inserting a new drive
- : Deleting the currently selected drive

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

246/301

Extended Functionality

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews:

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 248 / 304

Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews: