Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 200

Page: 200 / 304

10.1.5

Interrupting Connection

If the communication to the control is interrupted, no diagnostic messages can

be displayed. This is for example the case if the connection cable was removed.

The display of the diagnostic messages is deleted when the connection is in‐

terrupted. As soon as the connection is established again, the display updates

automatically.

10.2

Logbook

10.2.1

Overview

The logbook is embedded in the diagnostic display. After calling the diagnostic

display with <F9>, it can be switched to the "logbook" with <F7>.

Fig.10-10:

Start screen of the diagnostics

10.2.2

Logbook Selection

Open logbook

Logbooks are configured in IndraWorks Engineering. Any number of logbooks

can be combined with any controls. If more than one logbook was configured,

a selection dialog is opened when opening the logbook (<F7>). If only one log‐

book is configured, the selection dialog is not displayed but the logbook is

immediately activated.
If no logbook is configured, a warning message is displayed.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

198/301

Diagnostics

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews:

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 200 / 304

Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews: