Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 331

Page: 331 / 422

Fig. 10-14:

HAS05.1-024

10.10.3 Properties

●

Transmission of equipment grounding conductor, DC bus,

communication, module bus, signals of safety technology

●

Control voltages galvanically isolated between the zones before and

after the accessory

●

Allowed current: 15 A

●

Degree of protection: IP65

●

External power supply required (42 V

, ±10%; e.g., PULS

"CPS20.361" (100‑240 V, 480 W) or "QT20.361" (380‑480 V, 480 W)

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

317/407

Accessories

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual, Page: 331 / 422

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews: