Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 26

Page: 26 / 422

1.2.5

Overview of functions

Firmware functions (functional packages)

For the available firmware functions, see chapter "Functional

packages" in the Functional Description of the firmware used.

Hardware-related functional restrictions as compared to drive controllers with

separate control sections:
●

Safety technology: not all safety functions available

●

No analog inputs or outputs

●

No digital and analog I/O extensions

●

No additional encoder evaluations or encoder emulations

12/407

System presentation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands