manualshive.com logo in svg

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

The Bosch Rexroth IndraDrive Mi KCU02 is a state-of-the-art industrial drive controller. Unlock its full potential with the comprehensive Instruction Manual, available for free download on our website. This manual provides detailed guidance and insights to ensure smooth operation and maximum efficiency. Get yours now at manualshive.com!

Share
Download
background image

1.2.3 

Firmware

Firmware required to operate an IndraDrive Mi drive system:

Product
Series

Supported from firmware version

KSM02

MPB-17V08
"Safe Motion" safety technology:
MPB-18V08

KMS02 

MPB-17V10
"Safe Motion" safety technology:
MPB-18V08

KMS03 

MPB-20VRS

KMV03 

PSB-20VRS

Tab. 1-4:

Required firmware versions

1.2.4 

System structure

The supply unit that is used significantly defines the system structure.
Possible supply units:
●

Rexroth IndraDrive HMV01.1E/R or HMV02.1R supply unit

●

Rexroth IndraDrive HCS02.1E or HCS03.1E converter

●

Rexroth IndraDrive converter HCS01.1E-W0054 + HAS05.1-023

●

Rexroth IndraDrive KMV03.1R supply unit

The IndraDrive Mi drive system in the figure below contains KSM

motor-integrated servo drives. This system structure also applies

to IndraDrive Mi drive systems with KMS near motor servo drives.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03  

9/407

System presentation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive Mi KCU02

S-COM 7K Manual preview
7K
Brand: S-COM Pages: 400
2N NetSpeaker Quick Start preview
NetSpeaker
Brand: 2N Pages: 4
Samson 3354 Mounting And Operating Instructions preview
3354
Brand: Samson Pages: 40
Universal Remote Genesis MX-900 Manual preview
Genesis MX-900
Brand: Universal Remote Pages: 20
Matelec FPC-36040 Owner'S Operation Manual preview
FPC-36040
Brand: Matelec Pages: 16
praher SUPERSTAR E-3000/F2 Operating Instructions Manual preview
SUPERSTAR E-3000/F2
Brand: praher Pages: 10
IDEC HR6S-S Original Instructions Manual preview
HR6S-S
Brand: IDEC Pages: 97
Balluff BIS U-830-4-011-H-1 Quick Start Manual preview
BIS U-830-4-011-H-1
Brand: Balluff Pages: 2
Aqua Lung Cousteau/ SEA Service & Repair Manual preview
Cousteau/ SEA
Brand: Aqua Lung Pages: 24
Nexus 21 L-45 Installation Instructions Manual preview
L-45
Brand: Nexus 21 Pages: 24
Broadcast Tools WVRC-4 Installation And Operation Manual preview
WVRC-4
Brand: Broadcast Tools Pages: 39
Weber Markoprint iJET Operating Manual preview
Markoprint iJET
Brand: Weber Pages: 127
Neles Easyflow J7 DN15 Installation Maintenance And Operating Instructions preview
Easyflow J7 DN15
Brand: Neles Pages: 12
Quasar LINCOLN Series Quick Manual preview
LINCOLN Series
Brand: Quasar Pages: 4
Lennox HYDROCONTROL Installation, Operating And Maintenance Manual preview
HYDROCONTROL
Brand: Lennox Pages: 34
Rohde ST 630 Operation Manual preview
ST 630
Brand: Rohde Pages: 344
Yuga CLM920_TE5 Hardware Manual preview
CLM920_TE5
Brand: Yuga Pages: 39
WAREMA climatronic Control panel 3 Series Installation And Connection preview
climatronic Control panel 3 Series
Brand: WAREMA Pages: 64

Brands by name

Popular brands

Load more brands