Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 19

Page: 19 / 422

Components

Features

RKH, hybrid cable

●

RKH0xxx

–

DC bus connection

–

Control voltage and signal exchange cable

–

Communication cable

●

RKH0800

–

Mains voltage

–

Mains contactor

●

RKH0801

–

Mains choke

–

Mains voltage synchronization

●

The hybrid cable is supplied in ready-made form with connectors.
The bulk cable (hybrid cable without connector) is named REH0800

(hybrid cable incl. communication) or REH0803 (hybrid cable without

communication; devices with external communication (ES option) use

separate cables for communication).

Tab. 1-1:

IndraDrive Mi with KMS03 – Features

Cooling types

Thermal interface

(cold plate, insulated mounting)

Forced cooling

Natural convection

Tab. 1-2:

Cooling types (example: KMV03)

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

5/407

System presentation

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands