Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 165

Page: 165 / 422

6.2.7

X53, Control Voltage Output

High electrical voltage! Danger to life by

electric shock!

WARNING

Do not remove connectors when the component has been powered. Do not

plug in connectors when the component has been powered.
Wait at least 30 minutes after switching off the supply voltages to allow

discharging.

View

Connection

Signal name

Function

1 (WH*)

GND

●

Output of DC-DC converter (24V – 42V) in

KCU02
(GND is not connected to 0V of the 24V

supply)

●

Supplies KSM02/KMS02 with control

voltage

2 (GN*)

42 V

Screw terminal (connector at hybrid

cable)

Unit

Min.

Max.

Tightening torque

1,5

1,7

Connection cable stranded wire

Connection via hybrid cable RKH

Connection cable

AWG

Output data

out

, P

out

(see technical data of KCU02)

Short circuit protection

–

Present

Overload protection

–

Present

Conductor color of the ready-made cable RKH

Tab. 6-10:

Function, Pin Assignment, Properties

Control Voltage Monitoring

The control voltage is constantly monitored. If the allowed voltage range is

left, the control voltage for the connected KSM02/KMS02 devices is switched

off and LED H53 emits red light. Thereafter, the motors are coasting down

because a return movement is no longer possible.

Notes on Operation

Do not remove connectors when the component has been powered. Do not

plug in connectors when the component has been powered.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

151/407

Connection points

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands