Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 265

Page: 265 / 344

Refresh

Before using a new battery, you always have to carry out the so-called "re‐

fresh" procedure:

Refresh resistor

Mating connector

Connector

Battery

Fig. 8-19:

Battery refresh procedure

Connect connector of battery to mating connector at refresh resistor.

Wait 2 minutes.

Disconnect connector from mating connector.

Replacing the battery

To maintain the absolute value encoder position when the battery is replaced,

the following requirements have to be fulfilled:
●

The control voltage at the drive controller has been switched on

●

The encoder has been connected to the drive controller via the encoder

cable

Fig. 8-20:

Control voltage switched on and encoder connected

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

263/341

Rexroth IndraDrive CsDrive Systems with HCS01

Cables, accessories, additional components

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands