background image

Ordering code

Part number

Description

RKB0008/007,5 (*******-*******-*******)

R911172971

Length: 7.5 m

RKB0008/010,0 (*******-*******-*******)

R911170153

Length: 10 m

RKB0008/015,0 (*******-*******-*******)

R911171183

Length: 15 m

RKB0008/020,0 (*******-*******-*******)

R911171184

Length: 20 m

RKB0008/025,0 (*******-*******-*******)

R911170154

Length: 25 m

RKB0008/030,0 (*******-*******-*******)

R911171381

Length: 30 m

RKB0008/035,0 (*******-*******-*******)

R911171369

Length: 35 m

RKB0008/040,0 (*******-*******-*******)

R911171382

Length: 40 m

RKB0008/050,0 (*******-*******-*******)

R911171383

Length: 50 m

Tab.  5-4:   Connecting cables to control cabinet PC, panel PC and operator display

Further cable lengths are available on request.

Two cables are always required to establish a connection between

the VxB and the VDP.

5.5  Wear Parts

Wear parts are not subject to any warranty.
Backlight
The service life of the backlight is limited. After this time has been exceeded,

the backlight will produce only 50 % of its original brightness. The service life is

approx. 50,000 hours at an ambient temperature of 25 °C.

6  Ambient Conditions

 

In operation

Transport

Storage

Max. ambient tempera-

ture

+0 

 to +50 

-20 

 to +60 

-20 

 to +60 

Max. temperature gradi-

ent

Temporal temperature

changes up to 3 K per

minute

Temporal temperature

changes up to 3 K per

minute

Temporal temperature

changes up to 3 K per

minute

VDP 15.3, 18.3, 21.3 Multitouch 

Bosch Rexroth AG

Ambient Conditions

DOK-SUPPL*-VDPXX.3MTBU-IT02-EN-P

7/37

Summary of Contents for Rexroth IndraControl VDP 15.3













































Reviews: