manualshive.com logo in svg

Bosch Rexroth IndraControl S20, Manual, Page: 70 / 88

Share
Download
Bosch Rexroth IndraControl S20 Manual Download Page 70

Error code

Error cause

Description

Solution

Dec

Hex

6155

0x180B

TUNID mismatch

The values of SNN and SDID en‐

tered at the DIP switch do not

match the values entered under

"Safe Configuration".

Compare the DIP switch position

with the values entered under

"Safe Configuration". Note that

0x600000000 is added to the SNN

value.

6156

0x180C

Data age of valid mes‐

sage greater than NTE

The exchanged data is older than

NTE

Increase the NTE value under

"Safe configuration".

6157

0x180D

Time coord. message

not received in allowed

time

The "time coordination message"

was not received in the expected

time

Increase the NTE value under

"Safe configuration".

6158

0x180E

Connection in use or

Duplicate For‐

ward_Open

It is either tried to reconfigure an

existing connection or a "forward

open" was sent twice.

The configuration of the new con‐

nection is incomplete: Ensure that

the SCCRC is provided with the

same value in "Safe Configura‐

tion" and in "Safe Parameteriza‐

tion". Check whether the "Safety

application" was compiled without

errors. Log in to the standard ap‐

plication to automatically apply the

required changes. "Duplicate For‐

ward open": Increase the NTE val‐

ue under "Safe configuration".

6160

0x1810

SafetyClose refer‐

enced an unknown

connection

The module received a Safety‐

Close with incorrect connection

parameters

Compare the DIP switch position

with the values entered under

"Safe Configuration". Note that

0x600000000 is added to the SNN

value.
Change SNN or SDID using DIP

switches. The saved connection

parameters are deleted upon a

new voltage startup.

6161

0x1811

Initialization not com‐

pleted within time limit

Connection could not be establish‐

ed.

Start the Safety application again.

6304

0x18A0

Operator made invalid

settings on DIP switch.

DIP switch position invalid. The

DIP switch position may not be 0

for SNN and SDID.

Set a value other than 0 for SNN

and SDID. Change SNN or SDID

using DIP switches. The DIP

switch values are applied after a

new voltage startup.

Tab. 13-3:

Parameter errors: CSos parameters

Bosch Rexroth AG

 DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

68/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

CSos parameters and device parameters

Summary of Contents for Rexroth IndraControl S20

























































































Reviews:

No comments