Bosch Rexroth HMU05.1N Series Project Planning Manual Download Page 97

Page: 97 / 410

4.6.2

Overall connection diagram (HMU05 as supply unit)

Overall connection diagram with load contactor

For your drive system, preferably use the connection with a load

contactor pictured here (instead of the connection with a control‐

lable main switch).

With multiple contactors connected in parallel, connect the N/O

contacts and N/C contacts in series.

Fig. 4-44:

Connection diagram with load contactor (HMU05 as supply unit)

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

95/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Summary of Contents for Rexroth HMU05.1N Series



























































































































































































































































































































































































































Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Bosch Rexroth HMU05.1N Series, Project Planning Manual, Page: 97 / 410

Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews: