Bosch Rexroth HMU05.1N Series Project Planning Manual Download Page 64

Page: 64 / 410

4.4.2

Control cabinet

Air cooling

Control cabinet design and cooling

The only mounting position allowed for supply units and drive

controllers to be installed in control cabinets is G1.

Possibilities of heat dissipation

Closed control cabinet with

air circulation

Closed control cabinet with

heat exchanger

Control cabinet with fan

Closed control cabinet with

air conditioning unit

~ 400 W

~ 1700 W

~ 2700 W

~ 4000 W

Dissipated heat output

Tab. 4-6:

Possibilities of heat dissipation

The section below describes the "control cabinet with fan".

Requirements for control cabinets

with fan

Risk of damage by unclean air in the control

cabinet!

NOTICE

Operating a control cabinet with a fan, but without the corresponding filters,

can damage the devices or cause malfunction.

●

Install filters at the air intake opening of the control cabinet so that un‐

clean air cannot get into the control cabinet.

●

Service the filters at regular intervals according to the dust loading in the

environment.

●

Only replace the filters when the fan has been switched off, because

otherwise the fan sucks in the dirt coming off the filter and the dirt gets

into the control cabinet.

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

62/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Summary of Contents for Rexroth HMU05.1N Series



























































































































































































































































































































































































































Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Brands by name

Popular brands

Bosch Rexroth HMU05.1N Series, Project Planning Manual

Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Brands by name

Popular brands