manualshive.com logo in svg

Bosch Rexroth HMU05.1N Series, Project Planning Manual

Share
Download
Bosch Rexroth HMU05.1N Series Project Planning Manual Download Page 291

Liquid-Liquid Heat Exchanger

Technical Information
General description of the machine

The machine is designed and manufactured for the purpose of cooling devi‐

ces or equipment by means of a liquid solution made of glycol and demineral‐

ised water.
The  cooling  system  is  mainly  based  on  the  exchange  of  heat  between  two

fluids  that  circulate  in  two  independent  circuits  (customer  side  circuit  and

drive circuit) and a heat exchanger.
The cold liquid, provided by the owner, flows in the customer side circuit and

through the heat exchanger it cools the liquid in the drive circuit.
The equipment or machine to be cooled is connected to the drive circuit.

Main parts

A

Electrical panel

B

Main pump

C

Filling pump

D

Heat exchanger

E

Expansion tank

F

Coolant distribution manifold

Fig. 8-77:

Main parts

DOK-INDRV*-HXX05******-PR02-EN-P 

Bosch Rexroth AG

289/407

Rexroth IndraDrive ML Drive Systems with HMU05

Cables, accessories, additional components

Summary of Contents for Rexroth HMU05.1N Series



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands