Bosch Rexroth H-4WEH...XE Series Operating Instructions Manual Download

Page: 25 / 52

Assembly 25/52

RE 24751-XE-B/04.16, H-4WEH...XE...,

Bosch Rexroth AG

7.4 Before the assembly

DAnGER

Explosion hazard due to the wrong area of application!

A valve which is not approved for the area of application may cause an explosion!

▶

Check whether the explosion protection marks on the name plate of the valve
comply with the information in these operating instructions.

▶

Check whether you have the correct valve type by means of the type designation
on the name plate of the valve.

▶

Check whether the zone assignment and the temperature class correspond to
the area of application of the valve.

▶

Check the scope of delivery for completeness and possible transport damage.

▶

Also observe the safety instructions in chapter 2.6 "Product-specific safety
instructions".

7.5 Required tools

In order to assemble the valve, you need standard tools only.

7.6 Required accessories

The following accessories are recommended for the connection of the valve. These
accessories are not included in the scope of delivery and can be ordered separately
from Bosch Rexroth:

For reasons of stability, exclusively use the following valve mounting screws.

Table 11: Valve mounting screws

Valve type

Type

Quantity Friction coefficient

according to
VDA 235-101

Material number

H-4WEH10... ISO 4762-M6x45-10.9-

flZn-240h-L

0.09...0.14

R913000258

H-4WEH16... ISO 4762-M10x60-10.9-

flZn-240h-L

0.09...0.14

R913000116

ISO 4762-M6x60-10.9-
flZn-240h-L

0.09...0.14

R913000115

H-4WEH25... ISO 4762-M12x60-10.9-

flZn-240h-L

0.09...0.14

R913000121

H-4WEH32... ISO 4762-M20x80-10.9-

flZn-240h-L

0.09...0.14

R901035246

For subplates with dimensions for valves with porting pattern according to
ISO 4401, refer to

"Data sheet 45100".

Valve mounting screws

Subplates

Summary of Contents for Rexroth H-4WEH...XE Series





















































Search results

Summary of Contents for Rexroth H-4WEH...XE Series

Reviews:

Related manuals for Rexroth H-4WEH...XE Series

Brands by name

Popular brands

Bosch Rexroth H-4WEH...XE Series, Operating Instructions Manual

Search results

Summary of Contents for Rexroth H-4WEH...XE Series

Reviews:

Related manuals for Rexroth H-4WEH...XE Series

Brands by name

Popular brands