Bosch Rexroth EcoDrive 03 Instruction Manual Download Page 31

Page: 31 / 36

Rexroth EcoDrive 03 DKC**.3-016

Instructions for Use

5-17

DOK-ECODR3-DKC16*UL***-IB01-EN-P

Fig. 5-35:

Example of arrangement for multiple-line structure with components

Arrangement of Cooling Units

CAUTION

Possible damage to the drive controller

Operational safety of the machine endangered!
Note the following instructions!

Due to the operating principle, condensation water is formed when cooling
units are used. For this reason, please observe the following information:

•

Always position cooling units in such a way that condensation water
cannot drip onto electronic equipment in the control cabinet.

•

Position the cooling unit in such a way that the blower of the cooling
unit does not spray accumulated condensation water onto electronic
equipment.

electronic

equipment

Eb0001f1.fh7

incorrect

correct

warm

cold

Cooling system

Cabinet

warm

cold

Air duct

electronic

equipment

Cabinet

Cooling system

Fig. 5-36:

Arranging the cooling unit on the control cabinet

Avoiding Dripping or Sprayed

Water

Summary of Contents for Rexroth EcoDrive 03





































Search results

Summary of Contents for Rexroth EcoDrive 03

Reviews:

Related manuals for Rexroth EcoDrive 03

Brands by name

Popular brands

Bosch Rexroth EcoDrive 03, Instruction Manual

Search results

Summary of Contents for Rexroth EcoDrive 03

Reviews:

Related manuals for Rexroth EcoDrive 03

Brands by name

Popular brands