Bosch rexroth CytroForce-M Operating Manual Download Page 25

Page: 25 / 85

25 / 85

Servo-hydraulic actuator

Product description

Bosch Rexroth AG

RE62270-B, 01.21

Fig. 3: Solution matrix

5.1.5

System Structure

The servo-hydraulic actuator can be easily implemented in your system. All rele-

vant signal cables of sensors and actuators are directly connected to the drive

controller. Command and actual values can be processed via common bus sys-

tems.

Fig. 4: System structure

5.1.6

Custom extension

A comprehensive portfolio of custom extensions is available for the servo-

hydraulic actuator.

Safety on board
The safety modules HSZ01, HAT02 and Safe Motion S4, which can be perfectly

integrated, allow the economic implementation of safety functions in accord-

ance with standards.

Summary of Contents for rexroth CytroForce-M






















































































Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands

Bosch rexroth CytroForce-M, Operating Manual

Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands