Bosch rexroth 4WS2EM10 5X XH Series Operating Instructions Manual Download Page 40

Page: 40 / 44

40/44

Technical data

Bosch Rexroth AG

, 4WS2EM10..5X/...XH..., RE29583-XH-B/09.19

Error

Possible cause(s)

Remedy

Hysteresis

• Control spool friction due to

contamination

Remove valve and have it repaired

Large zero point
deviation

• Orifice contaminated

Remove valve and have it repaired

External leakage

Seal defective
• Seal at the connection

surface is defective

Remove the valve and replace the seals

• Seal at filter screw is

defective

Disassemble the filter screw and replace
the seal

• Other leakage

Remove valve and have it repaired

Following faults due to contamination, in addition to the repair, it is essential to
check the oil quality and improve it, if necessary, by suitable measures such as
flushing or the additional installation of filters.

15 Technical data

For the technical data of your valve please refer to

"Data sheet 29583-XH"

16 Appendix

16.1 List of addresses

Bosch Rexroth AG
Bürgermeister-Dr.-Nebel-Straße 8
97816 Lohr am Main
Germany

Phone

+49 (0) 9352/40 50 60

[email protected]

Bosch Rexroth AG
Zum Eisengießer 1
97816 Lohr am Main
Germany

Phone

+49 (0) 9352/40 30 20

[email protected]

The addresses of our sales and service network and sales organizations can be found
at

www.boschrexroth.com/adressen

Contacts for service

and spare parts

Headquarters

Summary of Contents for rexroth 4WS2EM10 5X XH Series













































Search results

Summary of Contents for rexroth 4WS2EM10 5X XH Series

Reviews:

Related manuals for rexroth 4WS2EM10 5X XH Series

Brands by name

Popular brands

Bosch rexroth 4WS2EM10 5X XH Series, Operating Instructions Manual

Search results

Summary of Contents for rexroth 4WS2EM10 5X XH Series

Reviews:

Related manuals for rexroth 4WS2EM10 5X XH Series

Brands by name

Popular brands