Bosch Rexroth 3 Series Instruction Manual Download

Page: 7 / 68

About this documentation 7/68

RE 92105-01-B/06.2017, A4CSG, Series 3x,

Bosch Rexroth AG

1.3.2 Symbols

The following symbols indicate information that is not safety-relevant but increases
understanding of the documentation.

Table 3: Meaning of the symbols

Symbol

Meaning

If this information is disregarded, the product cannot be used and/or
operated to the optimum extent.

▶

Single, independent action

1.
2.
3.

Numbered instruction:
The numbers indicate that the actions must be completed one after the
other.

1.3.3 Designations

This documentation uses the following designations:

Table 4: Designations

Designation

Meaning

A4CSG

Axial piston variable pumpClosed circuit

Threaded plug

Metal screw, pressure-resistant

Protective plug

Made out of plastic, not pressure-resistant, only for transportation

As an umbrella term for “Axial piston variable pump A4CSG”, the designation “axial
piston unit” will be used in the following.

1.3.4 Abbreviations

This documentation uses the following abbreviations:

Table 5: Abbreviations

Abbreviation

Meaning

ATEX

EC directive on explosion protection (

mosphère

plosible)

DIN

eutsche

ndustrie

orm (German Institute for Standardization)

lectrohydraulic control with

roportional solenoid and pressure control

ISO

nternational

rganization for

tandardization

JIS

apan

ndustrial

tandard

exroth document in the

eutsch (German) language

VDI 2230

Directive for the systematic calculation of high duty screwed joints and
cylindrical screw joints from the VDI (

erein

eutscher

ngenieure -

Association of German Engineers)

Summary of Contents for Rexroth 3 Series





































































Search results

Summary of Contents for Rexroth 3 Series

Reviews:

Related manuals for Rexroth 3 Series

Brands by name

Popular brands

Bosch Rexroth 3 Series, Instruction Manual

Search results

Summary of Contents for Rexroth 3 Series

Reviews:

Related manuals for Rexroth 3 Series

Brands by name

Popular brands