Bosch Rexroth 3 Series Instruction Manual Download | Manualshive

Page: 60 / 68

background image

60/68 Troubleshooting

Bosch Rexroth AG

, A4CSG, Series 3x, RE 92105-01-B/06.2017

14.2 Malfunction table

Table 14: Axial piston unit malfunction table

Malfunction

Possible cause

Remedy

Unusual noises

Insufficient air bleeding of the hydraulic system

Fill the axial piston unit, suction line for the
hydraulic pump and the reservoir
Completely air bleed the axial piston unit and
hydraulic system
Check correct installation position

Insufficient suction conditions, e.g. insufficient
dimensioning of the suction line, viscosity of
the hydraulic fluid too high, suction height too
high, suction pressure too low, foreign particles
in the suction line, suction filter too small or
blocked

Machine/system manufacturer: check the
system, for example, optimize inlet conditions,
use suitable hydraulic fluid
Fill the suction line with hydraulic fluid

Remove foreign particles from the suction line

Check the filter system and change the filter as
necessary

Drive speed too high

Machine/system manufacturer: reduce drive
speed

Wrong direction of rotation

Machine/system manufacturer: check correct
direction of rotation, see chapter 7.4.1
“Preparation” on page 32

Improper mounting of the axial piston unit

Check the mounting of the axial piston unit
according to the specifications of the machine/
system manufacturer (observe tightening
torques)

Improper mounting of assembled parts,
hydraulic lines or improper installation of the
coupling

Mount assembled parts according to the
information provided by the coupling or fitting
manufacturer

Oscillate pressure limitation and pressure
control valves of the axial piston unit (boost
pressure-relief valve, high-pressure relief valve,
pressure cut-off)

Air bleed the axial piston unit and hydraulic
system
Contact Bosch Rexroth Service:
Optimize the settings of the pressure relief and
pressure control valves

Mechanical damage to the axial piston unit
(for example, bearing damage)

Replace axial piston unit

Contact Bosch Rexroth Service

Increased, unusual vibration

Bearings worn

Contact Bosch Rexroth Service

«
...
58
59
60
61
62
...
»

Summary of Contents for Rexroth 3 Series





































































Reviews:

No comments

Related manuals for Rexroth 3 Series

Brand: GD Pages: 55

Brand: Davey Pages: 8

Brand: Oleo-Mac Pages: 171

Brand: Oase Pages: 2

Brand: Bacharach Pages: 12

Brand: EBARA Pages: 16

Brand: EBARA Pages: 40

Brand: EBARA Pages: 38

Brand: GEA Pages: 78

Brand: Nachfolger Pages: 2

Brand: Navien Pages: 157

Brand: Navien Pages: 2

Brand: Navien Pages: 4

Brand: Paloma Pages: 24

Brand: Calpeda Pages: 32

Brand: RainSoft Pages: 16

Waterfall Kit WFK8

Brand: Beckett Pages: 1

Brand: Speck Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands