manualshive.com logo in svg

Bosch R901234567, Operating Instructions Manual

Share
Download
Bosch R901234567 Operating Instructions Manual Download Page 34

34/48 Operation

Bosch Rexroth AG

, 4WS2EM 10...XL..., RE29583-XL-B/09.20

9  Operation

9.1  General information

 WARNING

Explosion hazard caused by dust accumulations!

If the maximum dust layer thickness of > 50 mm is exceeded, there is an explosion 
hazard!

 

▶

Make sure that the maximum dust layer thickness is not exceeded.

 

▶

Regularly remove dust accumulations, if required.

 CAUTION

Loud noise!

An unfavorable arrangement of valves results in resonance or fluid noises, such as 
whistling. In continuous operation, these noises may cause hearing damage in 
persons or damage to the valves.

 

▶

In this case, contact a service engineer.

Only use the valve within the performance range provided in 

"Data sheet 29583-XL"

. 

The machine and/or system manufacturer is responsible for the correct project 
planning of the hydraulic system and its control.
Changing the settings at the valve is not admissible.

For information on the operation, please refer to the operating instructions for 
the hydraulic system into which the valve is installed.

If errors occur, refer to chapter 14 "Troubleshooting".

Summary of Contents for R901234567

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands