manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Configuration Manual, Page: 146 / 164

Share
Download
Bosch PRAESENSA PRA-AD604 Configuration Manual Download Page 146

146

en | Event messages

PRAESENSA

2020-09 | V1.20 | PRAESENSA 1.20

Configuration manual

Bosch Security Systems B.V.

Event: 

Message corrupt

 

Group

: Fault

Occurrence:

 Logs a checksum error of the configured messages.

Originator

: Device which had the mismatch.

Resolve: 

When the error is no longer present.

Recommended action

: Reload/restore the (involved) correct messages.

Extra information: 

Name(s) of message(s) with a checksum error.

18.2.2

Amplifier

The following 

fault

 events can occur 

only

 on amplifier devices.

Event: 

Temperature too high

 

Group

: Fault

Occurrence: 

Logs that a device in the system has an overheat fault.

Originator

: Device that has the overheat fault.

Resolve: 

When the Overheat fault is not present anymore.

Recommended action

:

–

Check the correct functionality of the device fan.

–

Check if the device/rack environment temperature is within specifications.

Event: 

Power supply fault: input A and/or B

 

Group

: Fault

Occurrence:

 Power supply fault: input A and/or B.

Originator

: Amplifier.

Recommended action

: Check/replace powering device (and/or amplifier), lines and

connections.

Event: 

Power supply fault: lifeline

 

Group

: Fault

Occurrence:

 Logs the failure of lifeline 18 V power supply to the controller of the amplifier.

Originator

: Amplifier.

Recommended action

: Check source (MPS) device lifeline, lines and connections. Check

MPS lifeline power supply output.

Event: 

Amplifier channel fault

 

Group

: Fault

Occurrence:

 Amplifier channel fault.

Originator

: Amplifier channel.

Recommended action

: Check input and output signals, lines and connections. Check/replace

amplifier.

Event: 

Output overload fault

 

Group

: Fault

Occurrence:

 Logs the channel output overload.

Originator

: Amplifier.

Recommended action

: Decrease the output load of the effected output channel(s).

Summary of Contents for PRAESENSA PRA-AD604





































































































































































Reviews:

No comments