manualshive.com logo in svg

Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20, Installation Manual

Share
Download
Bosch DSDA ISCSI DISK ARRAY SERIES DSA-N2B20 Installation Manual Download Page 30

28

en | Monitoring and Maintenance

DSDA iSCSI Disk Array Series

V 1 | 2008.08

Installation Guide

Bosch Security Systems

There are four LEDs on the power supply unit on the rear side of each shelf.

If either the 

Fan LED

 or the 

Power LED

 are lit 

amber

, the power supply unit must be replaced.

At the front side of each disk drive, there are two LEDs.

–

If 

no

 LED is lit, the drive is not recognized. Reinsert the drive.

–

If one LED is lit 

amber

, a fault is indicated. The drive must be replaced.

7.4

Software Update

i

NOTICE! 

Only Bosch certified software can be used.

i

NOTICE! 

To update the software, the system must reboot. During this process, no data can be written 

to the system.

i

NOTICE! 

If you are not using VRM, you need a program that functions as a Web server. 

For example, you can use 

AIDeX Mini-Webserver

 which can be downloaded from 

http://www.aidex.de/software/webserver/

.

Summary of Contents for DSDA ISCSI DISK ARRAY SERIES DSA-N2B20









































Reviews:

No comments

Brands by name

Popular brands

Load more brands