Bosch DICENTIS Configuration Manual Download Page 34 | Manualshive

Page: 34 / 134

Bosch DICENTIS Configuration Manual Download Page 34

34

en | Software installation

DICENTIS

2021.06 | V3.7 |

Configuration manual

Bosch Security Systems B.V.

Right-click the

DICENTIS Server Console

to:

–

Start services / Restart services / Stop services.

–

Use these options to manually Start/Restart/Stop the services.

–

Upgrade devices.

–

Use the firmware upgrade tool to upgrade the devices to the latest supported
version of the services (see

Downloading software to the devices, page 29 for

detailed information).

–

Activate licenses.

–

Click here to activate your licenses (see

Initial activation of the system, page 31

for

detailed information).

–

Start the activation tool

.

–

To add or remove licenses, see chapter

Adding and removing licenses, page 30.

An icon showing the status of the DICENTIS server is displayed:

Status

Description

Running

. The services are automatically started if there is a system license

(DCNM-LSYS) installed (checked every 20 minutes), and if the system can
connect to the database (checked every 60 minutes).

Note

: A network adapter

with a valid IP address is required for the services to start

Stopped

. Every 20/60 minutes, the system checks if the criteria are met and

will automatically stop or restart the services depending on the status.
If the services are stopped manually, the automatic check is also stopped.
If the system license is extended or reduced, the services must be restarted to
update to the current state.

Warning

. For example, this icon is displayed when a license is not activated.

How to permanently display the server console icon

By default, the server console icon is only displayed on event. To permanently display this
icon:
1.

Select the

Notification Area Icons

window:

–

Windows server 2012 R2 and Windows server 2016
Go to the Start screen and type notification. Filter the results by

Settings

, and then

click

Notification Area Icons

.

2.

Use the slider bar to scroll down to

DICENTIS Server Console.

3.

Select

Show icon and notifications.

4.

Click

OK.

The Server console icon will now be permanently displayed.

4.6

Rapid Spanning Tree Protocol (RSTP) support

The DICENTIS system supports redundant cabling when the Rapid Spanning Tree Protocol
(RSTP) is enabled. By default RSTP is disabled to prevent network failures in a system where
RSTP is not supported or allowed.
To enable cable redundancy:
1.

Power up the system without cable redundancy.

2.

Configure RSTP for

all

third party switches in the network.

«
...
32
33
34
35
36
...
»

Summary of Contents for DICENTIS







































































































































Reviews:

No comments