manualshive.com logo in svg

Bosch DICENTIS, Configuration Manual, Page: 108 / 134

Share
Download
Bosch DICENTIS Configuration Manual Download Page 108

108

en | Dante gateway

DICENTIS

2021.06 | V3.7 |

Configuration manual

Bosch Security Systems B.V.

13

Dante gateway

The Dante gateway is used to interface the DICENTIS system with other systems via Dante

TM

and when unicast Dante

TM

 streams or glitch free mode is required.

It has an OMNEO side with 2 Ethernet connectors for redundancy purposes, and a Dante

TM

side also with 2 Ethernet connectors for redundancy purposes.

The Dante gateway:
–

Combines multiple OMNEO devices into a single Dante

TM

 interface.

–

Receives 64 Dante

TM

 streams and sends them as 64 OMNEO streams, of which 16 can be

encrypted.

–

Receives 64 OMNEO streams, of which 16 can be encrypted, and sends them as 64
Dante

TM

 streams.

–

Converts multiple OMNEO encrypted flows with a single unicast or multicast stream into
a Dante

TM

 flow with multiple unicast or multicast streams.

–

Supports static routing with Dante Controller on the Dante

TM

 side and dynamic routing

(AES70) on the OMNEO side.

–

Allows glitch-free redundancy on the Dante

TM

 side and RSTP redundancy on the OMNEO

side.

–

Enables use of Dante Domain Manager

TM

 in combination with OMNEO systems.

i

Notice!

When OMNEO inputs or outputs 17 to 64 are used, these streams will be automatically set to
unencrypted mode by the DICENTIS system.

i

Notice!

The Dante gateway needs to be upgraded with the firmware delivered with the DICENTIS
system. The Firmware upload tool can be used to upload the correct firmware both on the
DICENTIS side and on the Dante

TM

 side.

To configure the OMNEO side, use the Meeting application:
1.

Open the Meeting application

2.

Go to 

Configure

 > 

Rooms

 > 

Floor and language routing

See 

Floor and language routing, page 82 for detailed information.

To configure the Dante

TM

 side, use the Dante Controller or the Dante Domain Manager

TM

.

Use OMNEO Control for configuring the network mode at the Dante

TM

 side. Please refer to the

OMNEO Control manual for more information. Download both OMNEO Control and the manual
can at: 

https://licensing.boschsecurity.com/omneo

.

i

Notice!

An OMN-DANTEGTW can receive up to 16 streams coming from the same transmitter stream.
If it receives 17 or more streams all coming from the same transmitter stream, then no stream
will be audible.

Summary of Contents for DICENTIS







































































































































Reviews:

No comments