manualshive.com logo in svg

Bosch B465, Installation And Operation Manual, Page: 38 / 115

Share
Download
Bosch B465 Installation And Operation Manual Download Page 38

38

en | Configuration and Diagnostics

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

12. Connect the B465 to the target computer, using a USB Type A to A cable. A New

Hardware Found window appears on the computer.

13. Browse to install the RBUS1CP.inf file found under the new hardware found on your

computer. Verify through the device manager that the appropriate .inf installs properly,
and is listed under the Ports (COMM & LPT) section. The correct .inf file is B465

 

Dual

Path Communicator.

14. Install a communication program to configure the B465.

Figure

 

6.1: RB_B465.inf installed inside Device Manager

6.2.1

Install TeraTerm

Install a serial communication program to establish communication from a computer to the
B465.

For your information

–

Windows Vista and Windows 10/8/7 installations no longer include a serial
communication program when the operating system installs. Install Tera Term from the
B465 user CD.

–

Windows XP.

 

The Microsoft Windows XP installation automatically installs HyperTerminal,

a Microsoft serial communication program, when Windows installs. If HyperTerminal is
not installed, install it from the Windows XP installation disc, or install Tera Term from
the B465 user CD.

Summary of Contents for B465




















































































































Reviews:

No comments