manualshive.com logo in svg

Bosch B465, Installation And Operation Manual, Page: 22 / 115

Share
Download
Bosch B465 Installation And Operation Manual Download Page 22

22

en | Installation

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

4.7.3

Control panel to dry contact wiring

Use the correct wire gauge when connecting a B465 to an intrusion/fire control panel terminal
(14-24AWG). Refer to the following figure for wiring information.

T

MPR

BAT

ET

HERNET

EXT

ERNAL

ANNUNC

X

MODULE 1

Y

MODULE

RELEASE

1    COM    2

3    COM    4

       T      R
PNL LINE 1

C      NO
RELAY 2

 

+

       

-

BATTERY

16.5VAC

NC    C    NO

RELAY 1

TRBL

TX

RX

PWR

PANEL
LINE 2

USB

ETHERNET

100BASE-T

LINK

COMMUNICATION  MODULE  1

3  COM  4

1  COM  2

R   Y    G

B

SDI2

Device Bus

BATTERY

PANEL
LINE 1

BATTERY

POWER

RX

TX

SYSTEM TROUBLE

INPUTS

2.2 k       End of

Line Resistors

C      NO
RELAY 3

12V

AUX COM

       T      R
PNL LINE 2

24 VDC

or

16.5 VAC

1

FIRE

ALARM

FIRE

SUPERVISORY

TROUBLE

2

4

3

5

ZONE INPUT

AUX/
COM

7

8

9

6

Figure

 

4.5: Panel to dry contact wiring

Callout 

ー

 Description

1 

ー

 Fire/intrusion control panel

2 

ー

 B465

3 

ー

 Fire alarm connection

4 

ー

 Fire supervisory connection

5 

ー

 Trouble (AC Fail, Low Battery, etc)

6 

ー

 Control panel EOL resistor (required for supervision with callout #8)

7 

ー

 Internal Ground (AUX power negative or internal Common) required for Commercial Fire

8 

ー

 Optional panel inputs for B465 troubles

9 

ー

 B465 EOL resistors

4.7.4

B46 module wiring (optional)

Use the cable supplied with the B46 to connect to the B465 module. Refer to 

System overview,

page 10

 section for component location. Refer to the figure below.

Summary of Contents for B465




















































































































Reviews:

No comments