manualshive.com logo in svg

Bosch B465, Installation And Operation Manual, Page: 16 / 115

Share
Download
Bosch B465 Installation And Operation Manual Download Page 16

16

en | Installation

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

1

2

3

1

1

1

2

Figure

 

4.1: Enclosure mounting (B10 shown)

Callout 

ー

 Description

1 

ー

 Enclosure mounting holes (4)

2 

ー

 3-hole mounting locations (3)*

3 

ー

 Tamper switch mounting locations

*Use the upper, right-hand 3-hole mounting location for installing the optional B46 module in
the enclosure so it lines up with the enclosure door hole.

4.3

Insert D101 lock (optional)

Refer to the instructions provided with the D101 for installation.

Notice!
Commercial fire requirement

The D101 lock is required for commercial fire installations.

4.4

Insert B46 LED cover (optional)

The B46 has an LED cover allowing users to view the B465 LED status indications outside the
enclosure.
1.

Punch out the enclosure knockout area.

2.

Insert the plastic LED cover into the knockout.

3.

Snap the cover into place.

4.

Make sure the cover is secure.

For more information, refer to the B46 Install Guide for more information.

Summary of Contents for B465




















































































































Reviews:

No comments