background image

62

en | Maintenance

AUTODOME inteox 7000i - 2MP (pendant)

2020-07 | 1.0 |

Installation Manual (pendant)

Bosch Security Systems

15

Maintenance

All bubbles require special care when handling and cleaning to avoid scratches.

Notice!

To avoid excessive moisture saturation inside the housing, limit the amount of time that the
bubble is disconnected from the housing. Bosch recommends that the bubble be removed
from the housing for no more than five (5) minutes.

Bubble Handling

The bubble may be packaged with a protective plastic sheet. It is recommended that the
bubble remain stored this way until it is ready to install. Limit handling the bubble, as any
scratches can quickly affect visibility.

Bubble Cleaning

If cleaning the bubble is required, use the following procedures and comply with all the
warnings listed below.

Cleaning the Bubble Interior

The extremely soft interior surface should not be cleaned by rubbing or dusting with a cloth.
Use clean dry compressed air, preferably from a spray can, to remove any dust from the
interior surface.

!

Warning!

Do not use alcohol-based solutions to clean the polycarbonate bubble. This will cause the
polycarbonate to cloud and over time cause stress aging, which makes the bubble brittle.

Cleaning the Bubble Exterior

The exterior of the polycarbonate bubble is hard coated for extra protection. If cleaning
becomes necessary, only use cleaning solutions and cloths suitable for cleaning safety glass
lenses. Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots. Never
scrub the bubble with any abrasive material or cleaners.
Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean &
Shine (or equivalent), according to manufacturer’s instructions. Refer to

www.novuspolish.com

 to order or to find a local distributor.

Cautions

Do Not clean bubbles in the hot sun or on very hot days.

Do Not use abrasive or highly alkaline cleaners on the bubble.

Do Not scrape the bubble with razor blades or other sharp instruments.

Do Not use Benzene, Gasoline, Acetone, or Carbon Tetrachloride on the bubble.

Summary of Contents for AUTODOME inteox 7000i 2MP



































































Reviews: