Bosch ARD-AYCE65B Installation Manual Download Page 8 | Manualshive

Page: 8 / 32

background image

8

en | Installation

ARD-AYCE65B

| V 1.1 | 2009.08

Installation manual

Bosch Sicherheitssysteme GmbH

3

Installation

Before starting, select the location to mount the ARD-AYCE65B.
This location should be at shoulder height.
For wall mounting, use the included mounting template as a
guide for drilling holes for mounting screws and wiring. For US
Gang Box mounting, no drilling is necessary.

Figure 3.1

Drilling & Mounting Template

Route the interface cable from the ARD-AYCE65B to the
controller. A linear type power supply is recommended.
Screw the ARD-AYCE65B to its mounting location or US gang
box.

«
...
6
7
8
9
10
...
»

Summary of Contents for ARD-AYCE65B

































Reviews:

No comments

Related manuals for ARD-AYCE65B

Brand: Panasonic Pages: 2

Brand: KAPTARLIFT Pages: 16

Brand: ShoreStation Pages: 19

Brand: Nedap Pages: 5

Brand: Vizio Pages: 24

Brand: Ruida Technology Pages: 35

Brand: Grace Digital Pages: 1

UltraTwin FreeSpan

Brand: Liko Pages: 10

Brand: Yaesu Pages: 39

I/O-SYSTEM 750-666/000-003

Brand: WAGO Pages: 166

Brand: RCA Pages: 2

Brand: Lutron Electronics Pages: 12

Brand: Sony Pages: 60

Brand: Sony Pages: 70

Brand: Silvercrest Pages: 24

Brand: Silvercrest Pages: 35

Brand: Silvercrest Pages: 42

Brand: Silvercrest Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands