manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 84 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 84

84

en | Programming sheets

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12

Installation Manual

Bosch Sicherheitssysteme GmbH

Zone Types 

Silent Alarm (Enable=1, Disable=0)

263

0 

EN=0

 

Zone alarm lock out time (disable=0, 1 times=1, 3 times=2, 6 

times=3, alarm duration=4)

264

0 

Support Detector Tamper (Disable=0, Enable=1)

265

1

Zone alarm report (Refer to zone report option)

266

6 

EN=1/5/

6/7

 

Zone Chime Mode (Enable=1, Disable=0)

267

0

Reserved

268-269

0

Zone #07 

Zone Type (Refer to zone type option)

270

1

Zone Bypass (Disable=0, Enable=1)

271

1

Forced Arming (Disable=0, Eanble=1)

272

1 

EN=0

 

Silent Alarm (Enable=1, Disable=0)

273

0 

EN=0

 

Zone alarm lock out time (disable=0, 1 times=1, 3 times=2, 6 

times=3, alarm duration=4)

274

0

Support Detector Tamper (Disable=0, Enable=1)

275

1

Zone alarm report(Refer to zone report option)

276

6 

EN=1/5/

6/7

 

Zone Chime Mode (Enable=1, Disable=0)

277

0

Reserved

278-279

0

Zone #08 

Zone Type (Refer to zone type option)

280

1

Zone Bypass (Disable=0, Enable=1)

281

1

Forced Arming (Disable=0, Enable=1)

282

1 

EN=0

 

Silent Alarm (Enable=1, Disable=0)

283

0 

EN=0

 

Zone alarm lock out time (Disable=0, 1 times=1, 3 times=2, 6 

times=3, alarm duration=4)

284

0

Support Detector Tamper (Disable=0, Enable=1)

285

1

Zone alarm report(Refer to zone report option)

286

6 

EN=1/5/

6/7

 

Zone Chime Mode (Enable=1, Disable=0)

287

0

Reserved

288-289

0

Zone Type

Description

0

Zone not used

1

Instant

2

Interior Instant

3

Delay

4

Interior  Delay

5

Follower

6

Interior Follower

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments