English |
11
LED worklight with status indicator
The LED worklight
(8)
is used as a status indic-
ator for device protection and low battery
status:
LED
Feedback
Description
Flashing light 3x
during operation
Battery status is low.
The voltage level of the battery has fallen
below the optimum value. The perform-
ance of the device is restricted.
Flashing light 3x
during downtime
Device protection is active.
Device protection has been activated to
prevent the battery from consuming a
large amount of power and to protect the
device against damage.
– If the battery status is low, charge the battery
(6)
or re-
place the weak battery with a fully charged battery.
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch
(10)
to varying extents.
A light pressure on the on/off switch
(10)
results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Preselecting torque (applies to screwdriving mode)
The torque presetting ring
(3)
can be used to pre-select the
required torque in 20 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
u
Only operate the gear selector (5) when the power
tool is not in use.
First gear:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Second gear:
High speed range; for working with a small drilling diameter.
u
Always push the gear selector switch as far as it will
go.
Otherwise, the power tool may become damaged.
Temperature-dependent overload protection
When used as intended, the power tool cannot be over-
loaded. In the event of overloading or the temperature rising
outside the permitted operating temperature range, the
speed will be reduced. The power tool will not run at full
speed again until the permitted operating temperature has
been reached.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder
(1)
, are
locked when the on/off switch
(10)
is not pressed.
This enables screws to be screwed in even when the battery
(6)
is empty and allows the power tool to be used as a
screwdriver.
Practical advice
u
Only apply the power tool to the screw when the tool
is switched off.
Rotating application tools can slip off.
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
Belt clip (accessory)
You can use the belt clip to hang the power tool on a belt, for
example. You then have both hands free and the power tool
is always at hand.
The accessory described here is not included with the
product as standard.
Maintenance and Service
Maintenance and Cleaning
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at:
www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: [email protected]
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
Bosch Power Tools
1 609 92A 6GE | (20.12.2021)
