background image

9

/

14CBi, 14

/

19CBi, 19

/

24CBi

WALL MOUNTED BOILERS FOR CENTRAL HEATING

AND INDIRECT SUPPLY OF DOMESTIC HOT WATER

INSTALLATION AND

SERVICING INSTRUCTIONS

This appliance is for use with Natural Gas or LPG (Cat II 2H3P).

9/14CBi  GC NUMBER 41 311 50 (N.G.)   

9/14CBi  GC NUMBER 41 311 51 (LPG)

14/19CBi  GC NUMBER 41 311 52 (N.G.)          14/19CBi  GC NUMBER 41 311 53 (LPG)
19/24CBi  GC NUMBER 41 311 54 (N.G.)          19/24CBi  GC NUMBER 41 311 55 (LPG)

APPLIANCE OUTPUTS         

IMPORTANT: THESE INSTRUCTIONS APPLY IN THE UK ONLY

AND MUST BE LEFT WITH THE USER OR AT THE GAS METER

Read the instructions before starting work - they have been written to make

the installation easier and prevent hold-ups.

9/14CBi N.G.

Minimum     9.0 kW    

Maximum   14.0 kW

9/14CBi LPG

Minimum     10.0 kW   

Maximum   14.0 kW

14/19CBi N.G.

Minimum     14.0 kW    

Maximum   19.1 kW

14/19CBi LPG

Minimum     14.0 kW   

Maximum   19.1 kW

19/24CBi N.G.

Minimum     19.1 kW    

Maximum   23.5 kW

19/24CBi LPG

Minimum     19.1 kW   

Maximum   23.5 kW

Worcester supports the

Benchmark code of practice

Summary of Contents for 19/24CBI













































Reviews: