Bosch 0603011100, Original Instructions Manual

Page: 20 / 257

20 | English
Starting Operation
Inserting the battery
Note:
The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Insert the charged battery
(4) into the battery receptacle un-
til you feel it engage and it is securely locked in place.
Switching on/off
To switch on the power tool, press the lock-off switch (1)
first. Then press the on/off switch (2) and keep it pressed.
The worklight lights up when the on/off switch (2) is lightly
or fully pressed allowing the work area to be illuminated in
poor lighting conditions.
To
switch off the power tool, release the on/off switch (2) .
Note: For safety reasons, the on/off switch (2) cannot be
locked; it must remain pressed during the entire operation.
Controlling the stroke rate
You can variably adjust the stroke rate of the power tool
when it is on by pressing in the on/off switch
(2) to varying
extents.
Applying light pressure to the on/off switch
(2) results in a
low stroke rate. Applying increasing pressure to the switch
increases the stroke rate.
The required stroke rate is dependent on the material and
the work conditions and can be determined using practical
tests.
It is recommended that you reduce the stroke rate when
placing the saw blade on the workpiece and when sawing
plastic and aluminium.
During prolonged periods of use at a low stroke rate, the
power tool may heat up significantly. Remove the saw blade
and let the power tool run at the maximum stroke rate for
around three minutes to cool down.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted battery temperature range, the speed is reduced
or the power tool switches off. At reduced speed, the power
tool will run again at full speed once the permitted battery
temperature is reached or the load is reduced. If it automat-
ically shuts down, switch the power tool off, allow the bat-
tery to cool down, then switch the power tool back on.
The three LEDs in the battery charge indicator
(3) flash
quickly when the temperature of the battery is outside the
operating temperature range of −20 to +50 °C and/or the
overload protection has been triggered.
Working Advice
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
Switch the power tool off immediately if the saw blade
becomes blocked.
u
When machining small or thin workpieces, always use
a stable base or saw table (accessory).
Plunge cutting (see figure L)
u
Plunge cuts may only be applied to soft materials,
such as wood, gypsum board, etc.
For plunge cutting, use only short saw blades. Plunge cutting
is possible only with a mitre angle of 0°.
Place the power tool so that the front edge of the base plate
(7) rests on the workpiece, without the saw blade (11)
touching the workpiece, and switch it on. On power tools
with stroke rate control, select the maximum stroke rate.
Press the power tool firmly against the workpiece and allow
the saw blade to plunge slowly into the workpiece.
As soon as the base plate
(7) rests fully on the workpiece,
continue sawing along the required cutting line.
Parallel guide with circle cutter (accessory)
When working with the parallel guide with circle cutter (29)
(accessory), the workpiece must be no more than 30 mm
thick.
Remove the base for
Cut Control (10) from the base plate
(7) . To do this, push the base together gently and remove it
from the guide (21) .
Parallel cuts (see figure M ): Loosen the locking screw (28)
and slide the scale on the parallel guide through the guide
(21) in the base plate. Adjust the desired cutting width as a
scale value on the inside edge of the base plate. Retighten
the locking screw
(28) .
Circular cuts (see figure N ): Drill a hole large enough to push
the saw blade through on the cutting line within the circle to
be cut. Machine the drill hole with a router or file so that the
saw blade can lie flush with the cutting line.
Position the locking screw
(28) on the other side of the par-
allel guide. Slide the scale on the parallel guide through the
guide
(21) into the base plate. Drill a hole in the workpiece
in the middle of the section to be cut out. Insert the centring
tip
(30) through the inner opening of the parallel guide and
into the drilled hole. Adjust the radius as a scale value on the
inside edge of the base plate. Retighten the locking screw
(28) .
Coolant/lubricant
As the material heats up along the cutting line when cutting
metal, you should apply coolant or lubricant.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
1 609 92A 5Y0 | (27.05.2021) Bosch Power Tools