background image

10/19

 

CH30T

 

 

                

Made in China to TQB Brands Pty Ltd specifications 

 

P a g e

 | 

12

 

Visit us at www.tqbbrands.com.au

 

WARRANTY 

 

BORUM Industrial products have been carefully tested and inspected before shipment and are guaranteed 
to be free from defective materials and workmanship for a period of 12 months from the date of purchase 
except where tools are hired out when the guarantee period is ninety days from the date of purchase. 

Should  this  piece  of  equipment  develop  any  fault,  please  return  the  complete  tool  to  your  nearest 
authorised  warranty  repair  agent  or  contact  TQB  Brands  Pty  Ltd  Warranty  team 

 

[email protected]

. 

If upon inspection it is found that the fault occurring is due to defective materials or workmanship, repairs 
will be carried out free of charge.  This guarantee does not apply to normal wear and tear, nor does it 
cover  any  damage  caused  by  misuse,  careless  or  unsafe  handling,  alterations,  accident,  or  repairs 
attempted or made by any personnel other than the authorised TQB Brands Pty Ltd repair agent. 

This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms 
are not authorised. 

Your TQB Brands Pty Ltd guarantee is not effective unless you can produce upon request a dated receipt 
or invoice to verify your proof of purchase within the 12month period. 

 

Consumer Guarantee  

Our goods come with a guarantee that cannot be excluded under the Australian Consumer Law. You are 
entitled  to  a  replacement  or  refund  for  a  major  failure  and  compensation  for  any  other  reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail 
to be of acceptable quality and the failure does not amount to a major failure. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

All images and illustrations shown are for reference purposes only. All information, specifications and 
illustrations in this manual are based on the latest information available at the time of publication and 
are subject to change without notice. The information in this manual is periodically revised to ensure the 
latest information is included. Download the latest version of this manual and other related technical 
documentation fro

www.tqbbrands.com.au

 

  

 

Summary of Contents for CH30T














Reviews: