3B-390978NU – 10/18
Page 8
EN
BONNET GRANDE CUISINE
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
17.4
CLEANING THE CAVITY GASKET
In order to remove traces of grease or food scraps that can damage the gasket, regular and manual cleaning of the cavity gasket should be
performed on the inner and outer faces. Before cleaning, use water with soap or neutral and non-abrasive detergent with a sponge or a soft cloth to
remove the grease from the cavity gasket.
17.5
MAINTENANCE OF INTERNAL SURFACES
The general principle consists in not letting the following settle in certain places:
- Substances likely to become concentrated and so become corrosive.
- Settling of different minerals contained in water and likely to generate corrosion (walls) performance and life-duration (fan balancing,
exchanger dissipation, ..) problems.
A trolley or preheating plate (optional) must be used for the automatic wash cycle on 20 level ovens.
CLEANING, DEGREASING: Once a day (see section « Cleaning menu »)
DESCALING: Every day if necessary.
If there are any mineral deposits (whitish specks) as a result of un-softened water in the cooking chamber this must be removed daily.
For maximum efficiency of the descaling product without damaging the material and components of the oven, you should use an
appropriate descaler. The use of certain acids has an irreversible destructive effect that may cause significant damage. The
descaling product must contain corrosion inhibitors to prevent metal attack. It must also comply with legal requirements, in
particular for material intended to come into contact with foodstuffs.
Chemical products containing nitric acid are strictly prohibited. Recommended composition:
- Phosphoric acid <50%
- Corrosion inhibitor
Procedure:
Before descaling the cooking cavity, a cleaning cycle is required (see paragraph « Cleaning menu ») to dissolve any accumulated grease.
Manual descale:
- Run in steam mode at 60°C for 5 minutes
- Manually spray the surfaces to be treated with a descaling product specifically adapted for use on stainless steel thus the
composition recommended is : phosphoric acid with a concentration of less than 50% + tensio- active corrosion inhibitors, diluted to
a known level (conforming to the product label and its data sheet) and using suitable protective equipment (conforming to the product
hazard sheet).Thoroughly spray the areas with limescale deposits (Fans, elements, panelling).
- Leave the product to act for several minutes depending on the level of scaling.
- Rinse using the automatic rinse cycle (see paragraph « Cleaning menu »).
- Undertake a cleaning cycle (see paragraph « Cleaning menu »)
The optional automatic cleaning system is designed to introduce degreasing detergent and nothing else. Never use a descaling solution. This
could cause irreversible damage to your oven.
17.6
MATERIAL USED FOR COOKING CORROSIVE PRODUCTS
(Sea fish, sauerkraut)
The materials used intensively and regularly for cooking corrosive products, such as sea fish, sauerkraut, …, should be cleaned carefully and
systematically after each use.
18 PREVENTATIVE MAINTENANCE
The appliance must be isolated electrically during cleaning or maintenance and when replacing parts.
Subject
D
a
il
y
W
e
e
k
ly
M
o
n
th
ly
E
v
e
ry
y
e
a
r
(O
r
e
v
e
ry
3
0
0
0
h
)
Recommendations
Cleaning the external surfaces
x
Use the correct dose of cleaning product; Do not use
abrasive products.
Cleaning the cavity seal (all models) and bottom door seal
(20 levels)
x
Use the correct dose of cleaning product; Rinse
thoroughly; Do not use abrasive products.
Visual inspection of cavity seal (all models) and bottom
door seal (20 levels)
x
In case of damage, alert the after-sales service
Cleaning and descaling of internal surfaces
x
Respect cleaning product dosage; Rinse thoroughly;
Alert the after-sales service if any rust points appear.
Checking the amount of cleaning agent in the container
x
Replace the container as often as necessary
Checking the condition of the hose and of the base valve in
the cleaning agent container
Check when replacing the container / Clean the base
valve
Cleaning the electronic compartment ventilation openings
x
Visual check of the presence of inner door stops
x
Visual check of the condition of the lighting strip label
x
Clean if necessary with a non-aggressive and non-
abrasive degreaser. Rinse thoroughly. In case of
damage, alert the after-sales service
Visual inspection of the core probe (tip, cable, passage
through the bulkhead)
x
In case of damage, alert the after-sales service
Periodic maintenance by the after-sales service
x