Home
/
Bolin Technology
/
BC-7-4K20S-S6MNB
/
User Manual

Bolin Technology BC-7-4K20S-S6MNB, User Manual, Page: 47 / 59

Share

32 pages before
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59

Page: 47 / 59

Bolin Technology BC-7-4K20S-S6MNB User Manual Download Page 47

47

AUDIO

This item is set to OFF by default, user can set it to ON to enable camera MIC to capture audio signal.

RELOAD PRESET 1:

When this item is set to ON, preset 1 is set to Home position. The camera goes to Home position when it is
powered on or reset.

VIDEO FORMAT:

This Video Format selection will determine the video format of both SDI and HDMI.
You can change the video format by adjusting this item. Select the item, press “←” button to choose the video
format you want to set to, then press “→” (Pressing “→” button changes value on some product models) or
HOME button to confirm it. After you confirm your choice, press HOME button again to restore it. The camera
will reboot by itself. The new video format is activated.
You can cancel it by pressing the MENU button.

The video formats that you can select from are:

•

2160P: 29.97/25/23.98/24

•

1080P: 60/59.94/50/30/29.97/25/23.98/24

•

1080I: 60/59.94/50

•

720P: 60/59.94/50

MCU FW:

Software Version Number of MCU that is currently
running on the camera, you may need this information
for technical support.

FPGA FW:

Software Version Number of FPGA that is currently
running on the camera, you may need this information
for technical support.

True Dual Output video format setting

This camera supports Bolin True Dual Output
functionality, means that you can have relevant IP
streaming when SDI/HDMI video is set to any format you
want to set to. It takes SDI/HDMI video format setting as
priority.

The following table chart shows the relationship between
SDI/HDMI video format and IP video format.

  EXPOSURE
  WHITE BALANCE
  DETALL

>

PICTURE

  GAMMA
  NETWORK
  PAN TILT ZOOM

>SYSTEM

OSD

PELCO ID

1

IR-RECEIVE

ON

DISPLAY INFO

ON

PRESET MEMORY

ON

FACTORY RESET
TALLY MODE OFF
AUDIO OFF
RELOAD PRESET 1

ON

VIDEO FMT

2160P29.97

MCU FW: VOB210B32010AA006
FPGA FW: V027 4K

SYSTEM MENU

«
...
45
46
47
48
49
...
»

Summary of Contents for BC-7-4K20S-S6MNB




























































Reviews:

No comments